1. Your Washing Machine Has a Secret Filter That Needs Cleaning
You’re probably hip to the fact that your dryer has a filter that catches lint, and that you need to clean it nearly every time you dry clothes.
But did you know your clothes washer also may have a filter? Check your owner’s manual to see if your washing machine has accessible filters for drains, lint, and water supply hoses.
What it does: The filter catches lint, debris, and sometimes your pocket change. Typical filter locations include:
- Behind a removable front panel at the base of the machine
- Inside the washing drum near the top
- At the hot and cold inlet hoses
How to maintain it: If your washer has filters, inspect and clean them at least once each year to keep your machine running at peak efficiency. A clogged filter might be to blame for drainage problems and excessive vibration.
What it could cost you: $75 to $150 per hour if you have to call the repair guy.
2. Your Chimney Crown is Crying for Attention What it does: This cap of cement, or crown, covers the top of the masonry — the brick, stone, or block walls of your chimney — and prevents water, debris, and critters from getting in your home. It forms a collar around the flue — the part of a chimney that sticks out the furthest and is the fireproof channel for smoke, sparks, and heat.
The crown is slanted to shed water, but all that exposure to the elements puts stress on it, causing cracking and chipping. (Check your chimney and crown every year with an annual maintenance inspection.)
How to maintain it: Apply a layer of brushable crown sealer (yes, they actually have that specific product — about $60 per gallon) to heal it up. While you’re up there, you should:
- Spray exposed bricks with clear masonry sealer to protect against moisture. Use a garden sprayer.
- Add a stainless steel chimney cap with a spark arrestor, which prevents burning embers from escaping the chimney ($70 to 120).
Tip: Since we’re talking about roof work, we feel obligated to share some safety advice:
- Don’t get on the roof if you’re scared of heights, the roof is wet, or the pitch is 4-in-12 or steeper.
- Set up your ladder properly. (Fiberglass extension ladders are heavier than aluminum but help protect against electric shock from accidentally touching power lines.)
- Keep the work area free of tools and debris.
- Wear traction footwear, such as boots with soft soles.
- Wear a safety harness. (Buy one for $200; rent one for $30 per day.)
3. You’ve Been Misled About Power Washers
Those motorized washers are recommended as a panacea for all kinds of cleaning tasks, from blasting grit off driveways to cleaning siding and decking boards.
What it does: A power washer uses a motor to deliver water at extremely high velocity for blasting surfaces clean. If you’re not careful, you can:
- Dig mortar out from between bricks
- Force water up behind lap siding, getting moisture inside your walls where it can cause rot and mold
- Scour areas of softer wood grain from decking boards, leaving you with awkward ridges and gouges
- Tear vinyl siding and window frames
- Peel paint from exterior surfaces
- Hurt yourself (Never let kids play with a pressure washer!)
What it could cost you: Replacing deck boards costs about $2 per square foot. If you need to remediate mold because water got behind your siding, you could be looking at $500 to $6,000 or more.
4. Your Water Softener Has a Love-Hate Relationship with Salt
What it does: A softener removes minerals that make water hard by filtering the water through salt crystals. Water softeners protect against such hard-water problems as:
- Reduced cleansing action of soap
- Lime scale and buildup inside pipes
- Soap scum on shower walls
- A salt bridge is a hard crust that can form between the salt and the water entering the tank, preventing the salt from doing its job.
Solution: Use a long-handled tool, like a broom, to poke the salt bridge and break it up.
- Salt mushing occurs when dissolved salt forms a sludge at the bottom of the softener tank and prevents proper circulation of water. Solution: The cure is to completely drain the tank, removing any salt and residue. Using high-quality salt helps alleviate the problem.
What it could cost you: A complete replacement of plumbing pipes due to excess lime scale inside pipes costs $2,000 to $15,000.
5. Your Water Shutoff Valves are Stuck
What they do: Many of the water-supply tubes that connect to faucets and toilets throughout your house have shutoff valves that can close off the flow of water in an emergency, or if you’re changing out an appliance or fixture. You’ll find them:
- Under kitchen and bathroom sinks
- Behind toilets
- Behind the clothes washing machine
These valves aren’t used very often, sometimes not for years. Unfortunately, that’s a problem. Over time, the valve handles may become rusted in the open position and useless.
How you maintain them: Once each year, lubricate the valve stem (WD-40 is always good), let it sit for 15 minutes, then close and reopen the valve several times.
If you’re replacing any fixtures, we recommend quarter-turn, ball-type shutoff valves ($10). These valves use only a 90-degree turn of a handle to completely shut or open – making the turn off faster. They have a minimum of moving parts, and their simplicity makes them very reliable over the years.
What it could cost you: Thousands of dollars in water damage if a leak occurs.
6. Your Ducts are Leaking
What they do: You know forced-air ductwork channels warm or cool air around your house. But did you know changes in temperature cause ducts to expand and contract slightly? Over years, ductwork joints may work loose.
That’s bad news. In fact, Energy Star says that 20% to 30% of the air moving through ducts in attics, unheated basements, and crawl spaces leaks out through holes and poorly connected ducts.
How do you know? Some clues include:
- Utility bills that seem unusually high
- Rooms that seem like they never get warm or cool enough
- Strange, unexplained odors (It may be that ductwork has come apart, letting in earthy crawlspace smells and worse — mold spores.)
If you have any of those symptoms, it’s probably time to check your ductwork.
How to maintain them: Attics and basements are relatively easy to inspect. If you’re not squeamish about slithering through crawl spaces, you can check the ductwork under the house yourself. Repair holes and open seams with metal tape, not the familiar “duct tape” product.
Otherwise, call in a pro for a $100 to $200 duct test to determine if they’re leaking air.
What it could cost you: Hundreds of dollars in energy costs every year.
Tip: If you like scented air, sprinkle a few drops of an extract (cinnamon, vanilla) or essential oil (lavender, mint) on your furnace filter before you install it.